Last updated: 2026-10-30 · By Fix It or Replace editorial team
KitchenAid Ice Maker Not Working? Ice Maker Off, Shutoff Arm, Water Valve, Kinked Line, Filter, Freezer Temperature, Reset, Inlet Valve, Ice Maker Module — Fixes, Costs, Repair vs Replace (2026)
Quick answer
Most KitchenAid ice makers that stop are off, short on water, or too warm. KitchenAid's US Product Help ("Ice Maker Not Working - Troubleshooting") names four causes: a restricted water supply, freezer temperature, the ice maker turned off, and water filter problems. Check them cheapest first:
- Is the ice maker on? KitchenAid says it's often turned off by accident. On models with a wire shutoff arm, the arm must be down; an arm stuck up tells the ice maker the bin is full.
- Water supply. The house valve should be fully open, the line connected, and no kinks. KitchenAid says not to push the refrigerator too far back, which can pinch the line.
- Filter. A new filter that isn't locked in can cut off water. KitchenAid's test: remove the filter and dispense water. If water now flows, the filter was installed wrong; reinstall it. Replace it about every 6 months.
- Freezer temperature. Product Help says 0–5°F for best ice production; KitchenAid's blog says 0°F.
- Reset. Press and hold the ice maker's reset button for a few seconds, or, without one, unplug the refrigerator for 1 minute.
- New install? Wait 24 hours for the first ice and 3 days for full production (KitchenAid built-in guidance).
- Making ice but not dumping it? KitchenAid's side-by-side page says to unplug for 1 minute, then check again after a couple of hours.
Still nothing? The usual parts are the water inlet valve, the ice maker assembly or module, or, on door-dispenser models, the dispenser control board or the wires to the freezer door. KitchenAid's blog says a faulty motor or control module may need a professional.
Our partner pro call line is coming soon. Until then: if your appliance may still be under warranty, contact the manufacturer first. Otherwise, get two or three written quotes from local appliance repair companies, and ask about the diagnostic fee and the parts-and-labor warranty.
Verdict at a glance
| Your situation | What it usually means | Our verdict |
|---|---|---|
| Ice maker off or arm up; valve half closed; line kinked; new filter not seated; freezer above 5°F; installed less than 24 hours ago | Setting, water, or filter | ✅ Free fix (a filter costs a little) |
| Water reaches the fridge (the dispenser works) but the ice maker never fills; ice maker hums but won't harvest; ice frozen into the mold | Inlet valve, ice maker assembly or module | 🔧 Usually worth repairing |
| Ice maker and the door dispenser and display all quit together on a side-by-side; or the ice maker failure comes with a warm freezer on an older refrigerator | Door wiring, dispenser board, or a cooling problem | 🔧 / ♻️ Check the settlement note below first; for a cooling failure on an older fridge, run the calculator |
Safety check before any DIY (30 seconds)
Stop and don't start the DIY steps below if any of these is true:
- Keep fingers out of the ice maker while it's powered. The ejector and arm move without warning. Turn it off or unplug first.
- Unplug before you remove the ice maker, a panel, or the inlet valve. The valve sits on the back and is wired to line voltage.
- Shut the water off at the house valve before you loosen any water fitting.
- Water near outlets. If the line is leaking behind the fridge, turn off the water and unplug before you reach back there.
- Don't run the ice maker without a water supply. KitchenAid says an ice maker left on with no water can buzz and make the fridge and freezer too cold.
- Still under warranty (year 1)? Have KitchenAid service it. Removing a built-in refrigerator isn't covered by the warranty.
- Recall check: search your model on the CPSC recall site before paying for a repair (see "Recalls" below).
If none of these apply, the free checks below are safe for most owners.
Fix order at a glance (cheapest first)
| Order | What to try | Cost | DIY tier |
|---|---|---|---|
| 1 | Turn the ice maker on; lower the shutoff arm; seat the bin | Free | Easy |
| 2 | Check for a control lock; close the freezer door fully | Free | Easy |
| 3 | Open the house water valve fully; straighten the line | Free | Easy |
| 4 | Reseat the filter; run KitchenAid's no-filter test | Free | Easy |
| 5 | Freezer at 0–5°F; wait 24 hours | Free | Easy |
| 6 | Reset button, or unplug 1 minute | Free | Easy |
| 7 | Replace an old filter; flush the water system | Filter | Easy |
| 8 | Level the refrigerator (small or misshapen cubes) | Free | Moderate |
| 9 | Water inlet valve | Part, or pro visit | Moderate |
| 10 | Ice maker assembly or module | Part, or pro visit | Moderate → Advanced |
| 11 | Dispenser control board; freezer-door wiring | Pro visit | Pro only |
| 12 | Freezer not cold (fans, defrost, sealed system) | Pro visit | Pro only |
DIY tiers: Easy (no tools) · Moderate (unplugged, water off, basic tools) · Advanced (ice maker removal, wiring harness, multimeter) · Pro only (boards, door wiring, sealed system, or still under warranty).
Which KitchenAid refrigerator do you have?
Find the model and serial number on the label inside the fresh food section. KitchenAid is a Whirlpool Corporation brand, so its parts use Whirlpool-style W-, WP-, and WPW- part numbers.
| Type | Model prefix (examples) | Where the ice maker usually is | Notes |
|---|---|---|---|
| French door, bottom freezer | Often KRFF / KRFC / KRMF (check label) | Fresh food section or the freezer drawer, depending on model | Door-dispenser models have a separate ice bin in the door |
| Side by side | Often KRSF / KRSC (check label) | Freezer door | Some 2018–2021 models are named in a wire-harness settlement (see below) |
| Built-in | Often KBSD / KBFN / KBSN (check label) | Freezer | KitchenAid's built-in page covers new-install timing and the ¼-inch water line |
Prefixes are examples, not a full list. Your Owner's Manual shows where your ice maker's on/off control and reset button are.
Five-minute checks before you call anyone
- On/off and arm: is the ice maker switched on (or the arm down)? Is a control lock on? Is the bin pushed all the way in?
- Water test: press the door water dispenser (if you have one). No water at all points to the house valve, line, or filter. Water at the dispenser but no ice points to the ice maker side.
- Filter test: if you changed the filter recently, take it out and try the dispenser. Water now means the filter wasn't seated; reinstall it.
- Thermometer: put one in the freezer overnight. Aim for 0–5°F (Product Help) or 0°F (blog).
- Listen: with a full cycle due, you may hear water fill the mold. A buzz with no water points at the supply or the inlet valve.
- Look at the mold: cubes frozen in the mold but never dropped point at the ice maker's harvest cycle; reset it first.
- Cube size: small or hollow cubes point to low water flow (old filter, kink, or the wrong saddle valve) or an unlevel fridge.
How to know it's fixed: within 24 hours, the bin has fresh cubes and the arm or sensor stops production when it's full.
What KitchenAid says vs. what KitchenAid says (Product Help vs. the kitchenaid.com blog)
KitchenAid's two official sources mostly agree but differ on the details:
| KitchenAid Product Help: "Ice Maker Not Working - Troubleshooting" | kitchenaid.com blog: "Refrigerator Ice Maker Troubleshooting" and "How to Reset an Ice Maker" | |
|---|---|---|
| Freezer temperature | Set between 0 and 5°F for optimal ice production | Set to 0°F; fridge at 33–40°F |
| Reset | Hold the reset button a few seconds, or unplug 1 minute if there's no button | Run pre-reset checks first: control lock, door closed, bin seated, shutoff arm down, about 0°F, supply, filter; after a reset, allow time for a cycle |
| Water flow and small cubes | Valve fully open, no kinks, don't push the fridge too far back; filter installed correctly | Also: the wrong saddle valve can cause low pressure and small, hollow cubes; level the fridge; flush the water system every time you change the filter |
| Who fixes what | Settings, water, filter, reset | A clogged filter is easy; a faulty motor or control module may need a professional |
Our take: start at 0°F (it satisfies both). If the supply line uses a saddle valve and cubes are small, that's worth checking before you buy an inlet valve. Do the blog's pre-reset checks before you reset.
Not from KitchenAid: Fixr, a cost-guide site, gives water-line and ice-maker costs (see the cost table). Treat its numbers as national averages, not KitchenAid guidance.
KitchenAid ice maker signs and what they point to
KitchenAid's ice maker pages don't use a single code list for every model. Check your Owner's Manual for any display messages.
| Sign | KitchenAid's explanation | First fix (free) | If it continues | DIY tier |
|---|---|---|---|---|
| No ice, no water at the dispenser | Water supply restricted or off; filter not seated | Open valve; straighten line; reseat filter | Inlet valve; frozen line | Easy → Moderate |
| No ice, dispenser water OK | Ice maker off or arm up; freezer too warm | Turn on; lower arm; 0–5°F | Ice maker assembly or module; inlet valve | Easy → Advanced |
| Buzzing, fridge and freezer too cold | Ice maker on with no water supply | Turn the ice maker off until water is connected | — | Easy |
| Ice in the mold, nothing in the bin | Not dumping (side-by-side page) | Unplug 1 minute; check in a couple of hours | Ice maker assembly | Easy → Advanced |
| Small, hollow, or misshapen cubes | Low flow, wrong saddle valve, or unlevel fridge (blog) | New filter; flush; level the fridge | Inlet valve | Easy → Moderate |
| Slow ice on a new fridge | Normal break-in | 24 hours for first ice, 3 days for full production | — | Easy |
Which part each symptom points at:
| Symptom | Part most often involved | DIY tier |
|---|---|---|
| No water to the ice maker with a good supply and a seated filter | Water inlet valve | Moderate |
| Ice maker won't cycle or harvest after a reset | Ice maker assembly or module | Moderate → Advanced |
| Low flow after a long time on one filter | Water filter | Easy |
| Ice maker, dispenser, and display fail together (door-dispenser models) | Freezer-door wiring or dispenser control board | Pro only |
| Freezer above 5°F with the ice maker working | Cooling problem (fans, defrost) — see our KitchenAid not-cooling guide | Advanced → Pro |
Checks from KitchenAid US Product Help and kitchenaid.com (sources 1–4), checked 2026-10-30. The part mapping is our own from those pages and the Whirlpool-family part catalog on Sears PartsDirect.
Diagnose by symptom → likely part
Before you touch parts: Unplug the refrigerator and shut off the water at the house valve. Have towels ready.
1. No water reaches the ice maker
Likely cause: with the house valve open, the line straight, and the filter seated, the water inlet valve on the back of the fridge may not be opening. Low household pressure or the wrong saddle valve can also starve it (KitchenAid blog).
DIY difficulty: Moderate.
| Part | What it does | DIY difficulty |
|---|---|---|
| Water inlet valve | Opens to send water to the ice maker and dispenser | Moderate |
2. The ice maker gets water but won't make or drop ice
Likely cause: the ice maker assembly or its module (the motor and control that harvest the cubes). KitchenAid's blog says a faulty motor or control module may need a professional.
DIY difficulty: Moderate → Advanced.
| Part | What it does | DIY difficulty |
|---|---|---|
| Ice maker assembly | Mold, ejector, and controls in one unit | Moderate |
| Ice maker module | Motor and control that run the harvest cycle | Advanced |
3. Slow ice, small cubes, or weak water flow
Likely cause: an old or clogged water filter. KitchenAid recommends replacing it every 6 months, when the indicator comes on, or as needed, and flushing the system after each change.
DIY difficulty: Easy.
| Part | What it does | DIY difficulty |
|---|---|---|
| Water filter | Filters water to the dispenser and ice maker | Easy |
4. Ice maker, dispenser, and display all quit (door-dispenser models)
Likely cause: a dispenser control board or the wires that run into the freezer door. Some 2018–2021 KitchenAid side-by-side models are named in a wire-harness class settlement (see "Recalls" below).
DIY difficulty: Pro only.
| Part | What it does | DIY difficulty |
|---|---|---|
| Dispenser control board | Runs the door dispenser and, on some models, ice controls | Pro only |
Water on, filter seated, freezer cold, still no ice? A technician can test the inlet valve, ice maker, and door wiring in one visit.
Partner pro call line coming soon. See “who services” below for your options.
Independent partner service, not KitchenAid. We may be paid when you call.
Recalls (and one settlement that isn't a recall)
We searched the CPSC site on 2026-10-30 and didn't find a KitchenAid refrigerator or ice maker recall. The KitchenAid recalls we found were for cooktops and ranges.
Not a recall, but worth checking: a class-action settlement over Whirlpool-made refrigerators built 2018–2021 covers some KitchenAid side-by-side models (the settlement site lists KRSC500ESS01, KRSC700H*S00-04, KRSF505E01, KRSF705HPS00-04, KRSC503E01, KRSC703H*S00-04, and KRSF705HBS00-01). The lawsuit claims wires running to the freezer door can fail and knock out the ice maker, ice dispenser, water dispenser, or control panel. Whirlpool denies the claims. The settlement site describes reimbursement for some repair costs between years two and seven after purchase or manufacture, depending on proof. Not every unit with those model numbers is included; check your serial number and the current deadlines on the settlement site. We read it through search-index text and are not affiliated with it.
Search your exact model at cpsc.gov/Recalls.
Prevent it next time
- Replace the filter about every 6 months and flush the system after each change (KitchenAid).
- Leave a service loop of ¼-inch copper or PEX line and don't push the fridge too far back (KitchenAid).
- Clean the ice maker about every six months, more often with heavy use or hard water (KitchenAid blog; check your manual first).
- Keep the freezer at 0°F and the door fully closed.
- Keep the fridge level so water spreads evenly in the mold.
Related guides: KitchenAid refrigerator not cooling · KitchenAid refrigerator leaking water · Whirlpool ice maker not working · Maytag ice maker not working · GE ice maker not working · Frigidaire ice maker not working · Whirlpool freezer not freezing
What KitchenAid's warranty covers on a refrigerator
Per a KitchenAid Refrigeration Limited Warranty sheet (W10768783B; retailer-hosted copy, see Sources). Terms vary by model and year, so check your own sheet:
| Period (from original purchase) | What's covered | Who pays labor |
|---|---|---|
| Year 1 | Factory-specified replacement parts and repair labor for defects | KitchenAid |
| Years 2–5 | Cavity liner and sealed refrigeration system only | KitchenAid (parts and labor) |
| Years 6–10 | Sealed refrigeration system parts only | You pay labor |
What this means for an ice maker: the ice maker, inlet valve, and dispenser board are covered in year 1 only. Filters are consumables and aren't covered. KitchenAid excludes in-home instruction, improper installation (including household plumbing), food loss, and removing or reinstalling a built-in. Keep your proof of purchase.
→ KitchenAid Product Help: schedule service · KitchenAid 1-800-422-1230
Before you pay for any repair: a 4-point check
- Warranty: year 1 covers the ice maker; check retailer or credit-card extended protection.
- Recalls and settlement: search your model at cpsc.gov/Recalls; side-by-side owners, check the settlement serial lookup.
- Free fixes done: ice maker on, arm down, bin seated, valve open, line straight, filter seated, 0–5°F, reset, 24 hours.
- Written quote: ask for part, labor, and trip fee separately, and which part tested bad.
What it costs: repair parts and pro service (2026)
How we price this table: DIY part prices are Whirlpool-family part numbers listed on Sears PartsDirect public search pages for "kitchenaid refrigerator …" searches (S-list under Sources), USD before tax and shipping. GE (WR…), Samsung (DA…), LG, Amana-style unlabeled numbers, covers, housings, arms, trim panels, and user-interface assemblies in the same results were excluded. Ranges span several part numbers because the right part depends on your model number. Pro costs tagged [GUIDE] come from two US cost guides (Fixr = G1, HomeGuide = G2): national averages for refrigerators in general, not KitchenAid-specific quotes. "Varies — get a quote" means neither guide itemizes that repair, so we don't show a number.
| Repair | Part cost (DIY) | Typical pro cost (parts + labor) | Notes |
|---|---|---|---|
| Ice maker on, arm, valve, line, reset, filter reseat | $0 | — | Do these first |
| Water filter (everydrop) | $56.28–$75.14 (EDR6D1 to EDR1RXD1) [S3] | — | DIY |
| Water inlet valve | $61.62–$239.95 (W10408179 kit to W11243758) [S2] | [GUIDE] water valve replacement $100–$250 (G2) | |
| Ice maker assembly / module | $84.93–$220.92 (W10190935 module to W10190933 module); assemblies W11658802 $142.48 and W11557001 $155.52 [S1] | [GUIDE] ice maker repair $350–$500, most about $400 (G1); ice maker repair $100–$225, replacement $250–$600 (G2) | Model-specific |
| Dispenser control board | $201.73–$366.35 (W11221359 to W10789707) [S4] | [GUIDE] control board $500–$1,000 (G1); $400–$750 (G2) | Guide figures are for the main control board |
| Water line (dispenser and ice maker tubing) | — | [GUIDE] water line repair $140–$200 (G2) | |
| Service call | — | [GUIDE] service call $70–$120, labor $100–$250/hr (G1); minimum fee $70–$130, $50–$125/hr (G2) | |
| KitchenAid refrigerator repair (brand range) | — | Varies — get a quote (G1 doesn't list KitchenAid separately) | |
| New comparable refrigerator | — | [GUIDE] replacement $1,000–$3,000 (G1); $675–$2,500 (G2) |
Part prices checked 2026-10-30 on Sears PartsDirect public search pages (S1–S4). Pro-cost cells tagged [GUIDE] from G1 (Fixr) and G2 (HomeGuide), re-read 2026-10-30; [GUIDE] figures are national averages, not KitchenAid-specific quotes. Prices change; confirm with your model number.
Tip: tell the tech whether the door dispenser gives water, whether the ice maker hums or fills, the freezer temperature, and when you last changed the filter. That separates a supply problem from an ice maker problem.
Repair vs. replace calculator
1. What's the all-in repair cost? → R = trip/diagnostic fee + part + labor + tax, minus anything KitchenAid's warranty (or a settlement) covers
2. What does a comparable new refrigerator cost, all-in? → N = unit + delivery + installation + haul-away
3. How old is your refrigerator, and how long should it last? → Age and Life (use about 13 years, Fixr's average, inside HomeGuide's 10–20-year range, if you don't know)
4. How much have you spent on repairs in the last 2 years? → Past
Step A — Cost ratio: R ÷ N
Step B — Life used: Age ÷ Life
Step C — Repeat-repair check: (R + Past) ÷ N
| Life used under 50% | Life used over 50% | |
|---|---|---|
| Repair under 50% of new | ✅ Repair | 🤔 Repair is usually fine. Check for other wear |
| Repair over 50% of new | 🤔 Get a second quote first | ❌ Replace |
Repeat-repair rule: if Step C is over 50%, lean toward replacing. If the part is no longer available for your model, replace.
An ice maker is rarely a reason to replace a refrigerator that otherwise cools well. Many owners simply turn the ice maker off and buy ice for a while.
Worked example 1 (illustrative numbers): A new KitchenAid French-door makes no ice the first day. KitchenAid says wait 24 hours for first ice and 3 days for full production. R = $0.
→ Not a repair.
Worked example 2 (illustrative numbers): A 6-year-old KitchenAid side-by-side has water at the dispenser but no ice; a tech replaces the ice maker: R = $300; N = $2,800.
300 ÷ 2,800 = 11%; life used 6 ÷ 13 = 46% → Repair.
Worked example 3 (illustrative numbers): A 12-year-old KitchenAid French-door needs a dispenser board ($550 quote) after a fan last year ($300); the freezer also runs warm. N = $1,800.
550 ÷ 1,800 = 31%; life used 12 ÷ 13 = 92%; repeat check (550 + 300) ÷ 1,800 = 47%, close to the line → Get a second quote, and fix the cooling first; if that needs a big repair too, replace.
Tips toward replacing: the ice problem comes with a cooling failure on an older refrigerator, or repeat repairs.
Tips toward repairing: it's a filter, inlet valve, or ice maker; the fridge cools well; or it's in year 1.
Why 50%? It's the common rule of thumb; Fixr says never spend more than half the price of a new model on repairs. Some technician checklists draw the line a little higher, at about 60% of a new refrigerator's price, so treat a repair that costs 50–60% of new as a second-quote zone, not an automatic replace.
Who services KitchenAid refrigerators near you
1. KitchenAid (warranty). Schedule service through KitchenAid Product Help or call 1-800-422-1230. Have your model and serial number ready.
→ KitchenAid Product Help
2. A partner appliance pro (out of warranty).
Our call line connects you with an independent appliance repair provider in your area. Tell them whether the dispenser gives water, whether the ice maker fills, the freezer temperature, and your model number.
Our partner pro call line is coming soon. Until then: if your appliance may still be under warranty, contact the manufacturer first. Otherwise, get two or three written quotes from local appliance repair companies, and ask about the diagnostic fee and the parts-and-labor warranty.
Questions to ask any technician:
- Did you check water pressure and the saddle valve before replacing the inlet valve?
- Is it the whole ice maker or just the module?
- On a side-by-side, did you check the wires into the freezer door?
- Can you split the quote into part, labor, and trip fee?
Optional: is an appliance warranty worth it?
A home warranty (service contract) can cover repairs for a yearly fee plus a per-visit service fee. Read the exclusions carefully: plans often exclude ice makers, water filters, food loss, and pre-existing problems.
FAQ
Why is my KitchenAid ice maker not making ice?
KitchenAid's top causes: a restricted water supply, the freezer too warm, the ice maker turned off, or a filter problem. Open the valve fully, straighten the line, turn the ice maker on, and check the filter is seated.
How do I reset a KitchenAid ice maker?
Press and hold the reset button for a few seconds. If there isn't one, unplug the refrigerator for 1 minute. KitchenAid's blog suggests checking the arm, bin, door, and control lock first.
What temperature should my KitchenAid freezer be for ice?
KitchenAid's Product Help says 0–5°F; its blog says 0°F.
How long does a new KitchenAid ice maker take?
About 24 hours for the first ice and three days for full production (KitchenAid built-in guidance).
Can a water filter stop my KitchenAid ice maker?
Yes. A clogged or poorly seated filter can reduce or stop flow. Take it out and try the dispenser; if water now flows, reinstall the filter.
How much does it cost to fix a KitchenAid ice maker?
Often nothing. When we checked Sears PartsDirect on 2026-10-30, Whirlpool-family inlet valves listed at about $62 to $240 and ice maker modules at about $85 to $221. Fixr puts ice maker repair at $350 to $500; HomeGuide says $100 to $225.
About the author
Fix It or Replace editorial team — We research appliance repairs using manufacturer documentation, parts-supplier data, and current US cost guides, and we cite every source below. We are not appliance technicians; for wiring, board, or sealed-system repairs, call a qualified pro.
Last updated: 2026-10-30.
Sources
- KitchenAid Product Help (US): "Ice Maker Not Working - Troubleshooting" (causes: restricted water supply, freezer temperature, ice maker off, filter problems; valve fully open, line secure, no kinks, don't push the fridge too far back; freezer 0–5°F; reset button held a few seconds or unplug 1 minute; ice maker on without water: buzzing, fridge and freezer too cold; filter installation test by removing the filter and dispensing; replace every 6 months, at the indicator, or as needed; everydrop filters). https://producthelp.kitchenaid.com/Refrigeration/Full-Size_Refrigerators/Product_Info/Product_Assistance/Ice_Maker_Not_Working_-_Troubleshooting (accessed 2026-10-30)
- KitchenAid Product Help (US): "Not Making Ice - New Installation - Built In Refrigerator" (24 hours to first ice, three days for full production; cold water supply; ¼-inch OD soft copper or PEX; service loop; kinks; don't push too far back) and "Not Making Ice - Side by Side Refrigerator" (making ice but not dumping: unplug 1 minute, check after a couple of hours). https://producthelp.kitchenaid.com/Refrigeration/Full-Size_Refrigerators/Built_In_Refrigerator/Ice/Not_Making_Ice/New_Installation/Not_Making_Ice_-_New_Installation_-_Built_In_Refrigerator · https://producthelp.kitchenaid.com/Refrigeration/Full-Size_Refrigerators/Side_By_Side_Refrigerator/Ice_and_Water_Concerns/Ice_and_Dispenser_Concerns/Ice_Production/Not_Making_Ice/Not_Making_Ice_-_Side_by_Side_Refrigerator (accessed 2026-10-30 via search-index text)
- kitchenaid.com: "Refrigerator Ice Maker Troubleshooting" (clogged filter is easy, faulty motor or control module may need a professional; ice maker on, supply connected, valve open, arm down; filter every six months; freezer 0°F, fridge 33–40°F; small or hollow cubes: filter, kinks, wrong saddle valve, level; flush the water system as often as you change the filter). https://www.kitchenaid.com/pinch-of-help/major-appliances/refrigerator-ice-maker-troubleshooting.html (accessed 2026-10-30 via search-index text)
- kitchenaid.com: "How to Reset an Ice Maker and Check Common Issues" (pre-reset checks: on and no control lock, door closure, bin seated, shutoff arm down, about 0°F, supply, filter; allow time after a reset; clean the ice maker about every six months). https://www.kitchenaid.com/pinch-of-help/major-appliances/how-to-reset-an-ice-maker.html (accessed 2026-10-30 via search-index text)
- KitchenAid "Refrigeration Limited Warranty," W10768783B (©2015; sheet for KRSF505ESS), retailer-hosted copy (Coast Appliances): year 1 parts and labor; years 2–5 cavity liner and sealed system, parts and labor; years 6–10 sealed system parts only; exclusions incl. in-home instruction, improper installation, consumables, food loss, removal or reinstallation of built-ins; 1-800-422-1230. https://assets.coastappliances.com/product-assets/kitchenaid/refrigerators-and-freezers/KRSF505ESS/KRSF505ESS-warranty.pdf (accessed 2026-10-30)
- Whirlpool Refrigerator Settlement, "FAQs" (class settlement, not a recall; Whirlpool-manufactured refrigerators made 2018–2021; KitchenAid models KRSC500ESS01, KRSC700H*S00-04, KRSF505E01, KRSF705HPS00-04, KRSC503E01, KRSC703H*S00-04, KRSF705HBS00-01; claimed wire failures to the freezer door affecting ice maker, dispensers, control panel; Whirlpool denies the claims; relief for years two to seven; serial lookup). https://refrigeratorsettlement.com/faqs (accessed 2026-10-30 via search-index text)
- U.S. Consumer Product Safety Commission: recalls search (no KitchenAid refrigerator recall found 2026-10-30). https://www.cpsc.gov/Recalls (accessed 2026-10-30)
- Federal Trade Commission: endorsement and affiliate disclosure guidance. https://www.ftc.gov/business-guidance/resources/ftcs-endorsement-guides-what-people-are-asking
- Part prices (Sears PartsDirect, S-list) and repair cost guides (Fixr G1, HomeGuide G2), see lists below (accessed 2026-10-30).
Part price sources (Sears PartsDirect public search results, USD, accessed 2026-10-30; Whirlpool-family part numbers only; prices change, confirm with your model number):
- S1. Searches "kitchenaid refrigerator ice maker" and "kitchenaid refrigerator ice maker module": ice maker assemblies W11658802 $142.48, W11557001 $155.52; modules W10190935 $84.93, 8201515 $91.14, W10190933 $220.92 (shutoff arm extension, cover, cube ejector, housing, top panel, and LG, Samsung, GE, and Frigidaire listings excluded). https://www.searspartsdirect.com/search?q=kitchenaid%20refrigerator%20ice%20maker · https://www.searspartsdirect.com/search?q=kitchenaid%20refrigerator%20ice%20maker%20module
- S2. Search "kitchenaid refrigerator water inlet valve": W10408179 kit $61.62, WP67003753 $75.15, WP67005154 $77.19, WP2188786 $115.53, W10853654 $118.35, WP2313917 $119.58, WP2188785 $128.78, WPW10445780 $145.64, WP2317883 $147.64, WP12544002 $183.84, WPW10159843 $184.85, WPW10159839 $199.01, W10876668 $229.34, W11243758 $239.95 (12002193 excluded). https://www.searspartsdirect.com/search?q=kitchenaid%20refrigerator%20water%20inlet%20valve
- S3. Search "kitchenaid refrigerator water filter": everydrop EDR6D1 $56.28, EDR2RXD1 $66.37, EDR4RXD1 $70.82, EDR3RXD1 $72.94, EDR5RXD1 $73.85, EDR1RXD1 $75.14 (filter cap excluded). https://www.searspartsdirect.com/search?q=kitchenaid%20refrigerator%20water%20filter
- S4. Search "kitchenaid refrigerator dispenser control board": W11221359 $201.73, WP2303843 $222.40, W11330971 $265.93, W10789707 $366.35 (GE WR55X, Samsung DA92/DA94, LG ABQ, and user-interface assembly W10844896 excluded). https://www.searspartsdirect.com/search?q=kitchenaid%20refrigerator%20dispenser%20control%20board
Pro-cost guide sources [GUIDE] (US national averages, parts + labor, not brand-specific quotes; the guide pages carry 2023–2025 dates, so local quotes may differ):
- G1. Fixr, "How much does it cost to repair a refrigerator?" (updated August 29, 2025): ice maker repair $350–$500, most about $400 with one new part; control board $500–$1,000; service call $70–$120; labor $100–$250 per hour; replacement $1,000–$3,000; average life 13 years; never spend more than half the price of a new model on repairs. https://www.fixr.com/costs/refrigerator-repair (accessed 2026-10-30)
- G2. HomeGuide, "How Much Does Refrigerator Repair Cost? (2026)" (byline April 5, 2023): ice maker repair $100–$225, ice maker replacement $250–$600; water valve $100–$250; water line repair $140–$200; control board $400–$750; $50–$125 per hour, minimum call-out $70–$130; replacement $675–$2,500; refrigerators last 10–20 years. https://homeguide.com/costs/refrigerator-repair-cost (accessed 2026-10-30)
Disclosure
Fix It or Replace is an independent site. We are not affiliated with, endorsed by, or sponsored by KitchenAid or Whirlpool Corporation. "KitchenAid" is a trademark of its owner and is used here only to describe the products we cover.
- Affiliate links: Some part links go to retailers such as PartSelect and RepairClinic. If you buy through them, we may earn a commission at no extra cost to you.
- Call line: Phone numbers labeled "partner pro" are operated by a third-party lead service that routes your call to an independent repair provider in your area. We may be paid for calls. We don't employ the technicians, and we don't guarantee their work, pricing, or availability. Confirm licensing, insurance, and quotes directly with the provider.
- Prices are estimates and change often. Always get a written quote.
- Safety: Unplug the refrigerator and shut off the water before removing the ice maker or inlet valve. If you're unsure, call a qualified professional.
We don't publish fake reviews or testimonials, and we never present a tracking phone number as a specific local business.