Last updated: 2026-10-30 · By Fix It or Replace editorial team
Amana Dryer Not Heating? Air Only, Both Breakers, 240 V Cord, Gas Valve, Lint Screen, Vent, L2 Code, Thermal Fuse, Heating Element, Thermostats, Igniter, Gas Valve Coils — Fixes, Costs, Repair vs Replace (2026)
Quick answer
First, confirm it really isn't heating. Amana's test: pick a heated Timed Dry cycle, run it empty for 5 minutes, then open the door and feel inside. Warm inside but loads still damp? That's a vent or airflow problem, not a heat failure.
Amana's order of checks when it's truly cold:
- Not on Air Only. Air Only or Air/Fluff Only never adds heat.
- Electric: both breakers. Amana says electric dryers need a separate 30-amp circuit with two breakers: one runs the motor, the other the heating element. If one trips, the drum turns but there's no heat.
- Electric: 240 V and the cord. The dryer needs 240 volts. Check the 3- or 4-wire cord is installed per the instructions and the terminal screws are tight (unplugged). If in doubt, call a qualified electrician.
- L2 on the display means low or no line voltage keeping the heater off; it shows at initial installation.
- Gas: valve open. The drum turns but there's no heat if the gas shutoff valve is closed. It's open when the handle is parallel to the pipe.
- Lint screen and vent. Amana's article says clean the lint screen every load, and use a 4-inch rigid or flexible metal vent that isn't clogged, crushed, or kinked.
All of that fine and still cold? The usual parts on Whirlpool-built Amana dryers: a blown thermal fuse or thermal cut-off (almost always from a restricted vent), a failed heating element (electric), thermostats, or the igniter or gas valve coils (gas).
Repair or replace? Fuses, thermostats, elements, igniters, and coils are inexpensive. These repairs are usually worth it.
Our partner pro call line is coming soon. Until then: if your appliance may still be under warranty, contact the manufacturer first. Otherwise, get two or three written quotes from local appliance repair companies, and ask about the diagnostic fee and the parts-and-labor warranty.
Verdict at a glance
| Your situation | What it usually means | Our verdict |
|---|---|---|
| Air Only selected; one breaker tripped; L2 after an install; gas valve closed; dryer warm in the 5-minute test but loads damp | Setting, power, gas supply, or vent | ✅ Free fix. Change the cycle, reset breakers, open the valve, clean the vent |
| Cold after all the checks; heat stopped after a stretch of long dry times; gas dryer clicks but never lights | Thermal fuse or cut-off, heating element, thermostats, igniter, valve coils | 🔧 Usually worth repairing |
| F# E# that returns; burning smell or scorch marks; dryer 10+ years old with a second big repair in about 2 years | Board, wiring damage, or repeat failures | ♻️ Lean toward replacing if the quote passes about half of a new dryer |
Safety check before any DIY (30 seconds)
Stop and don't start the DIY steps below if any of these is true:
- You smell gas. Don't touch switches. Leave, and call your gas utility from outside.
- You smell burning, see scorch marks, or a breaker keeps tripping. Leave it off and call a technician or electrician.
- Unplug before any panel comes off and before checking the cord terminal screws (Amana). For gas, close the gas valve too.
- Gas burner parts (igniter, valve coils, flame sensor) are near the gas line. If you aren't confident, this is a pro job.
- The vent is crushed, kinked, disconnected, or packed with lint. That's a fire risk, and it's what blows the thermal fuse. Fix it before replacing parts.
- The dryer is in its first year. Use Amana's warranty service before removing panels.
- Recall check: search your model on the CPSC recall site before paying for a repair.
If none of these apply, the free checks below are safe for most owners.
Fix order at a glance (cheapest first)
| Order | What to try | Cost | DIY tier |
|---|---|---|---|
| 1 | 5-minute empty heated Timed Dry test | Free | Easy |
| 2 | Pick a heated cycle, not Air Only / Air Fluff | Free | Easy |
| 3 | Electric: check both breakers; gas: one breaker or fuse | Free | Easy |
| 4 | Gas: open the shutoff valve (handle parallel to the pipe) | Free | Easy |
| 5 | Clean the lint screen; clean and straighten the vent | Free, or vent service | Easy → Moderate |
| 6 | Electric: check 240 V, cord, terminal screws (unplugged) | Free, or electrician | Moderate |
| 7 | Thermal fuse; thermal cut-off and high-limit thermostat | Part, or pro visit | Moderate |
| 8 | Electric: heating element; cycling thermostat | Part, or pro visit | Advanced |
| 9 | Gas: igniter, gas valve coils, flame (radiant) sensor | Part, or pro visit | Advanced |
| 10 | Control board; wiring | Pro visit | Pro only |
DIY tiers: Easy (no tools) · Moderate (basic tools, one panel, multimeter) · Advanced (heater or burner access) · Pro only (boards, gas you aren't confident with, or still under warranty).
Which Amana dryer do you have?
Find the model and serial number on the label inside the door opening or on the back of the dryer. You need it to get the right fuse, element, or igniter.
| Type | Model prefix (examples) | Heat source | What usually stops the heat |
|---|---|---|---|
| Electric | Often NED (check label) | Heating element; 240 V, two breakers | One tripped breaker; thermal cut-off, element, thermostats |
| Gas | Often NGD (check label) | Gas burner and igniter; one breaker or fuse | Closed valve; igniter, valve coils, flame sensor |
| Older Amana dryers | Varies (check label) | Either | Some use older Amana- or Maytag-era part numbers |
Labeling note: Amana is a Whirlpool brand, and Amana's Product Help pages carry the same text as Whirlpool's. The parts Sears PartsDirect lists under Amana dryers are mostly Whirlpool-family numbers (WP-, W-, 279-), plus some older Amana and Maytag-era numbers. Prefixes are examples, not a full list; confirm with your model's parts diagram.
Five-minute checks before you call anyone
- The heat test. Empty drum, heated Timed Dry, 5 minutes, feel inside.
- Cycle. Make sure Air Only / Air Fluff isn't selected.
- Breakers (electric). Find both dryer breakers. Switch each fully off, then on. A half-tripped double breaker can leave the drum turning with no heat.
- Display. L2 = low or no line voltage. AF or F4 E3 = restricted airflow. F# E# = needs service.
- Gas valve (gas). Handle parallel to the pipe = open.
- Lint screen. Clean it. If there's detergent residue, Amana says scrub it with hot water, liquid detergent, and a nylon brush.
- Vent. Pull the dryer out. Look for a crushed or kinked vent, and check it's 4 inches in diameter and metal. Check for air at the outside hood.
How to know it's fixed: the 5-minute empty heat test feels clearly warm.
Vent cleaning: Amana's two pages give different intervals
| Amana Product Help: "Dryer is Not Heating" | amana.com article: "3 Reasons Your Dryer Isn't Heating or Drying" | |
|---|---|---|
| How often to clean the house vent | Every one to two years, or as needed when drying performance drops | Every year; also recommends a professional vent cleaning service once a year |
| Who should do it | You, or a professional vent cleaning service | A professional is recommended (Whirlpool recommends professional or qualified cleaning services) |
| Extra checks it lists | Vent testing kit sold on amana.com | Lint screen every load; 4-inch, rigid or flexible metal vent |
Our take: follow the stricter advice: clean the vent yearly, and sooner if loads take longer or the thermal fuse has blown. A blown fuse with a dirty vent is a sign to clean the vent first.
Amana dryer codes linked to no heat
| Code | Amana's explanation | First fix (free) | If it continues | DIY tier |
|---|---|---|---|---|
| L2 | Low or no line voltage keeps the heater off; dryer keeps running; shows during initial installation | Check both breakers or fuses and the cord; select a heated Timed Dry and restart | Amana: consult a qualified electrician | Easy → Pro |
| AF / F4 E3 | Restricted airflow: lint screen or vent clogged, crushed, kinked, or too many turns | Clean the lint screen and vent | Re-route or replace the vent | Easy → Moderate |
| F# E# | The control has detected a problem that requires service | — | Contact Amana or schedule service | Pro only |
| PF | Power failure interrupted the cycle | Touch and hold Start, or press Power to clear | Check breakers | Easy |
Amana's L2 page adds a power cycle: breakers off 5 minutes, back on, start a Timed Dry cycle, and watch 5 minutes for the code to return.
Which part each symptom points at:
| Symptom | Part most often involved | DIY tier |
|---|---|---|
| Electric, cold, after long dry times | Thermal cut-off (on the heater) or thermal fuse | Moderate |
| Electric, cold, cut-off tests good | Heating element | Advanced |
| Heats a little, then goes cold, or runs too hot | Cycling thermostat or high-limit thermostat | Moderate |
| Gas: igniter doesn't glow | Igniter (or flame sensor) | Advanced |
| Gas: igniter glows, then goes off without a flame | Gas valve coils | Advanced |
| Dead, no tumble, after a clogged vent | Thermal fuse (see Whirlpool dryer not starting) | Moderate |
Codes from Amana US Product Help (sources 1–4), checked 2026-10-30. The part mapping is our own from those pages and the Whirlpool-family part catalog. We used the open ApplianceDB sample's Whirlpool dryer entries (source 13) only as a cross-check.
Diagnose by symptom → likely part
Before you touch parts: Unplug the dryer. For gas, close the gas valve. Test parts with a multimeter for continuity only when unplugged.
1. Electric: tumbles, no heat, after long dry times
Likely cause: the thermal cut-off on the heater housing or the thermal fuse on the blower housing. Parts sellers (not Amana) say a blown fuse or cut-off means the vent was restricted, and the cut-off kit is sold with a high-limit thermostat as a set.
DIY difficulty: Moderate.
| Part | What it does | DIY difficulty |
|---|---|---|
| Thermal cut-off (kit) | Kills heat if the high limit fails | Moderate |
| Thermal fuse | Cuts power when the exhaust overheats | Moderate |
| High-limit thermostat | Turns the heat off if it overheats | Moderate |
2. Electric: cold, fuses test good
Likely cause: an open heating element coil, or a failed cycling thermostat.
DIY difficulty: Advanced.
| Part | What it does | DIY difficulty |
|---|---|---|
| Heating element | Makes the heat | Advanced |
| Cycling (operating) thermostat | Turns the heat on and off to hold temperature | Moderate |
3. Gas: igniter never glows
Likely cause: a failed igniter, an open flame (radiant) sensor, or the thermal fuse/cut-off.
DIY difficulty: Advanced (gas line nearby).
| Part | What it does | DIY difficulty |
|---|---|---|
| Igniter | Glows to light the gas | Advanced |
| Flame (radiant) sensor | Tells the dryer the burner lit | Advanced |
4. Gas: igniter glows, then goes out with no flame
Likely cause: failed gas valve coils, which open the valve after the igniter heats.
DIY difficulty: Advanced.
| Part | What it does | DIY difficulty |
|---|---|---|
| Gas valve coils (kit) | Open the gas valve | Advanced |
Gas dryer and not confident around the burner? A technician can test the igniter, sensor, and coils in one visit.
Partner pro call line coming soon. See “who services” below for your options.
Independent partner service, not Amana. We may be paid when you call.
Prevent it next time
- Clean the lint screen every load (Amana); scrub off detergent residue.
- Clean the vent yearly (the stricter of Amana's two intervals).
- Use a 4-inch metal vent; keep it short and free of crushes and kinks.
- Don't overload the drum.
- Check the outside hood for lint or nests.
Related guides: Whirlpool dryer not heating · Maytag dryer not heating · GE dryer not heating · Samsung dryer not heating · Amana washer not spinning · Kenmore dryer not heating · GE dryer not starting
What Amana's warranty covers on a dryer
Per the Amana Major Appliance Limited Warranty on amana.com (read 2026-10-30; your model's document has the final terms):
| Period | What's covered | Who pays labor |
|---|---|---|
| Year 1 (from delivery of the original purchase) | Factory-specified replacement parts and labor to correct defects in materials or workmanship, or replacement at Amana's discretion | Amana |
| After year 1 | No standard Amana coverage (extended service plans sold separately) | You |
What this means for a dryer that won't heat: in year 1, a failed fuse, element, thermostat, igniter, coil, or board is covered. All warranty service is done by authorized Amana service providers; you need proof of the original purchase date. Amana doesn't cover service calls to correct installation, instruct you on use, or fix house fuses, wiring, or plumbing, so a tripped breaker, an L2 wiring issue, or a clogged house vent isn't a warranty repair.
→ Amana: owners and service · Amana Customer eXperience Center 1-866-616-2664 (US)
Before you pay for any repair: a 4-point check
- Warranty: year 1 parts and labor; retailer or credit-card extended protection.
- Recalls: search your model at cpsc.gov/Recalls.
- Free fixes done: heat test, cycle, breakers, gas valve, lint screen, vent.
- Written quote: ask for part, labor, and trip fee separately, and whether they checked the vent if a fuse blew.
What it costs: repair parts and pro service (2026)
How we price this table: DIY part prices are part numbers listed on Sears PartsDirect public search pages for "amana dryer …" searches (S-list under Sources), USD before tax and shipping. Those searches also return GE, LG, Samsung, Frigidaire, and Speed Queen parts; we excluded them and kept Whirlpool-family, Amana, and Maytag-era numbers. The "amana dryer thermal fuse" search returned no listings, so thermal fuse prices come from the "whirlpool dryer thermal fuse" search (Whirlpool-built Amana dryers use these; confirm by model). Pro costs tagged [GUIDE] come from two US cost guides (Fixr = G1, HomeGuide = G2): national averages for dryers in general, not Amana-specific quotes. "Varies — get a quote" means neither guide itemizes that repair, so we don't show a number.
| Repair | Part cost (DIY) | Typical pro cost (parts + labor) | Notes |
|---|---|---|---|
| Cycle, breakers, gas valve, lint screen | $0 | — | Do these first |
| House vent cleaning | — | [GUIDE] clogged vent $80–$185 (G2); vent replacement $75–$150 (G1) | Fix before replacing fuses |
| Thermal fuse | $19.10–$49.40 (WP3390719 to WP33001762) [S1] | [GUIDE] thermal fuse $75–$150 (G2) | |
| Thermal cut-off kit / high-limit thermostat | $12.99–$78.59 (W11050897 kit to WP3391914) [S2] | [GUIDE] thermostat $100–$260 (G1); $100–$300 (G2) | |
| Cycling (operating) thermostat | $15.01–$113.22 (WP3398128 to WPW10168174) [S3] | [GUIDE] thermostat $100–$260 (G1); $100–$300 (G2) | |
| Heating element (electric) | $50.54–$265.69 (279838 to 61928) [S4] | [GUIDE] heating element replacement $150–$350 (G1); $150–$350 (G2) | |
| Igniter (gas) | $28.26–$71.63 (279311 kit to WP33002789) [S5] | [GUIDE] igniter $100–$250 (G1, G2) | |
| Gas valve coils (gas) | $26.08–$93.60 (279834 kit to 58804A) [S6] | [GUIDE] coil $150–$300 (G1); $100–$200 (G2) | Full valve W10622154 $223.72 |
| Flame (radiant) sensor (gas) | $25.91 (WP338906) [S7] | Varies — get a quote (not itemized in G1/G2) | |
| Control board | — | [GUIDE] control board $250–$500 (G2) | Rarely the cause of no heat |
| Service call | — | [GUIDE] service fee $50–$80, labor $50–$100/hr (G1); minimum fee $70–$130 (G2) | |
| New comparable dryer | — | [GUIDE] new dryer $600–$1,500 (G1); $800–$1,200 unit (G2); all brands |
Part prices checked 2026-10-30 on Sears PartsDirect public search pages (S1–S7). Pro-cost cells tagged [GUIDE] from G1 (Fixr) and G2 (HomeGuide), re-read 2026-10-30; [GUIDE] figures are national averages, not Amana-specific quotes. Prices change; confirm with your model number.
Tip: tell the tech whether it's electric or gas, whether the igniter glows, and whether loads were taking longer before the heat stopped.
Repair vs. replace calculator
1. What's the all-in repair cost? → R = trip/diagnostic fee + part + labor + tax, minus anything Amana's warranty (or a recall) covers
2. What does a comparable new dryer cost, all-in? → N = unit + delivery + installation + haul-away (+ new cord, gas connector, or vent kit)
3. How old is your dryer, and how long should it last? → Age and Life (use about 10 years, inside Fixr's 8–12 and HomeGuide's 8–13 ranges, if you don't know)
4. How much have you spent on repairs in the last 2 years? → Past
Step A — Cost ratio: R ÷ N
Step B — Life used: Age ÷ Life
Step C — Repeat-repair check: (R + Past) ÷ N
| Life used under 50% | Life used over 50% | |
|---|---|---|
| Repair under 50% of new | ✅ Repair | 🤔 Repair is usually fine. Check for other wear |
| Repair over 50% of new | 🤔 Get a second quote first | ❌ Replace |
Repeat-repair rule: if Step C is over 50%, lean toward replacing. If the part is no longer available for your model, replace.
Worked example 1 (illustrative numbers): A new Amana electric dryer tumbles but stays cold and shows L2. One leg of the double breaker had tripped. Resetting it fixes the heat. R = $0.
→ Not a repair.
Worked example 2 (illustrative numbers): A 6-year-old Amana electric dryer stops heating after months of slow drying. The thermal cut-off is open and the vent is crushed behind the dryer. A tech fits a cut-off kit and replaces the vent: R = $250; N = $850.
250 ÷ 850 = 29%; life used 6 ÷ 10 = 60%; repeat check 29% → Repair (and keep the vent clean).
Worked example 3 (illustrative numbers): A 12-year-old Amana gas dryer needs valve coils and an igniter, a year after a motor ($300): R = $320; N = $900.
320 ÷ 900 = 36%; life used 12 ÷ 10 = over 100%; repeat check (320 + 300) ÷ 900 = 69% → Replace, or repair only if you plan a short stay.
Tips toward replacing: repeat failures on an older dryer, heat damage to wiring, or parts no longer available.
Tips toward repairing: it's a fuse, cut-off, thermostat, element, igniter, or coils; the dryer is under about 7 years old; or it's covered.
Why 50%? It's the common rule of thumb, and the one we use. Some technician checklists draw the line a little higher, at about 60% of a new dryer's price, so treat a repair that costs 50–60% of new as a second-quote zone, not an automatic replace.
Who services Amana dryers near you
1. Amana (warranty). Warranty service is done by authorized Amana service providers. Contact Amana or schedule service through Amana Product Help, or call 1-866-616-2664.
→ Amana: owners and service
2. A partner appliance pro (out of warranty).
Our call line connects you with an independent appliance repair provider in your area. Tell them electric or gas, any code (L2, AF, F# E#), whether the igniter glows, and your model number.
Our partner pro call line is coming soon. Until then: if your appliance may still be under warranty, contact the manufacturer first. Otherwise, get two or three written quotes from local appliance repair companies, and ask about the diagnostic fee and the parts-and-labor warranty.
Questions to ask any technician:
- Did you check the vent before replacing the fuse or cut-off?
- Which part tested bad (element, thermostat, igniter, coils)?
- Can you split the quote into part, labor, and trip fee?
- What warranty do you give on your labor?
Optional: is an appliance warranty worth it?
A home warranty (service contract) can cover repairs for a yearly fee plus a per-visit service fee. Read the exclusions carefully: plans often exclude vent cleaning and damage from a clogged vent.
FAQ
Why is my Amana dryer running but not heating?
Amana's checks: Air Only selected; one of the two breakers tripped (electric); the 240 V cord; the gas valve closed (gas); a clogged lint screen or vent. After that, a thermal fuse or cut-off, heating element, thermostat, igniter, or valve coils.
How do I test whether my Amana dryer is heating?
Amana says run a heated Timed Dry cycle empty for 5 minutes, then open the door and feel inside. If it's warm, the problem is drying performance (usually the vent), not heat.
What does L2 mean on an Amana dryer?
Low or no line voltage keeping the heater off. Amana says check the breakers or fuses and the power cord, restart a heated Timed Dry, and consult a qualified electrician if it persists.
Where is the thermal fuse on an Amana dryer?
Parts sellers (not Amana) place it on the blower housing on Whirlpool-built models. It's one-time; replace it, and fix the vent that blew it.
Why does my Amana gas dryer igniter glow but not light?
Often failed gas valve coils. A technician can test them, along with the igniter and flame sensor.
How often should I clean my Amana dryer vent?
Amana's Product Help says every one to two years; Amana's article says every year. We suggest yearly.
How much does it cost to fix an Amana dryer that won't heat?
Often nothing. When we checked Sears PartsDirect on 2026-10-30, heating elements listed under Amana dryers ran about $51 to $266 and igniters about $28 to $72. Fixr and HomeGuide put a heating element replacement at $150 to $350.
Should I replace an Amana dryer that won't heat?
Rarely: most no-heat parts are inexpensive. Consider it when repeat repairs pass half the price of a new dryer on a dryer near 10 years old.
About the author
Fix It or Replace editorial team — We research appliance repairs using manufacturer documentation, parts-supplier data, and current US cost guides, and we cite every source below. We are not appliance technicians; for gas, wiring, or control boards, call a qualified pro.
Last updated: 2026-10-30.
Sources
- Amana Product Help (US): "Dryer is Not Heating" (5-minute empty heated timed cycle test; Air Only / Air Fluff adds no heat; heating but long dry times → vent; clean house vent every one to two years or as needed; vent testing kit; electric: separate 30-amp circuit, two breakers, one for the motor and one for the heating element; 240 V; 3- and 4-wire cord; tight terminal screws, unplug first; gas: shutoff open when the handle is parallel to the pipe). https://producthelp.amana.com/Laundry/Dryers/Product_Info/Dryer_Product_Assistance/Dryer_is_Not_Heating (accessed 2026-10-30)
- Amana Product Help (US): "Not Heating - Electric Dryer" and "Not Heating - Gas Dryer" (same heat test and Air Only check; electric breakers and cord; gas supply connected, valve open; household breaker or fuse). https://producthelp.amana.com/Laundry/Dryers/Dryer/Operation/Not_Heating/Not_Heating_-_Electric_Dryer · https://producthelp.amana.com/Laundry/Dryers/Dryer/Operation/Not_Heating/Not_Heating_-_Gas_Dryer (accessed 2026-10-30)
- Amana Product Help (US): "Error Codes in Dryers" (AF or F4E3 restricted airflow, lint screen or vent clogged, crushed, kinked, or too many turns; F# E# requires service; L2 low or no line voltage, keeps the heater from turning on, only during initial installation, check breakers and cord, restart Timed Dry, consult a qualified electrician; PF power failure, touch and hold Start or press Power). https://producthelp.amana.com/Laundry/Dryers/Product_Info/Dryer_Product_Assistance/Error_Codes_in_Dryers (accessed 2026-10-30)
- Amana Product Help (US): "L2 - Error Code - Dryer" (cycle power: breakers off 5 minutes, on, Timed Dry, monitor 5 minutes). https://producthelp.amana.com/Laundry/Dryers/Dryer/Error_Codes/Other_Error_Codes/L2_-_Error_Code_-_Dryer (accessed 2026-10-30)
- Amana US: "3 Reasons Your Dryer Isn't Heating or Drying" (240 V; gas supply and valve; lint screen every load, detergent residue scrubbed with hot water, liquid detergent, and a nylon brush; rigid or flexible metal vent, 4 inches in diameter; vents cleaned every year; professional vent cleaning once a year recommended; crushed or kinked venting). https://www.amana.com/articles/3-reasons-your-dryer-isnt-heating-or-isnt-drying.html (accessed 2026-10-30)
- Amana Product Help (US): "Dryer Vent may be Blocked or Restricted" (long dry times, very warm cabinet, steam, water behind the dryer, little lint, no air movement; lint buildup, nests, kinks). https://producthelp.amana.com/Laundry/Dryers/Product_Info/Dryer_Product_Assistance/Dryer_Vent_may_be_Blocked_or_Restricted (accessed 2026-10-30)
- Amana: "Major Appliance Limited Warranty" (W11655290 Rev A; one year from delivery of the original purchase, factory-specified replacement parts and labor, or replacement at Amana's discretion; service by authorized Amana Service Providers; exclusions incl. correcting installation, instruction, house fuses, wiring, plumbing; US 1-866-616-2664). https://www.amana.com/content/dam/global/documents/202305/warranty-w11655290-revA.pdf (accessed 2026-10-30)
- Third-party parts sellers (not Amana): PartSelect "Amana Dryer Fuses" (thermal fuse on the blower housing, one-time; thermal cut-off kit with a high-limit thermostat, fails from restricted airflow) and Repair Clinic WP3392519 (blown fuse indicates a restricted vent). Link only. https://www.partselect.com/Amana-Dryer-Fuses.htm · https://www.repairclinic.com/PartDetail/Thermal-Fuse/WP3392519/2986 (accessed 2026-10-30)
- iFixit (third party, not Amana): "How to Troubleshoot an Amana Electric Dryer That Won't Heat" (240 V check; heater components on Whirlpool-made designs; replace the high-limit cutoff and nearby heater thermostat as a set). Link only. https://www.ifixit.com/Guide/How+to+Troubleshoot+an+Amana+Electric+Dryer+That+Won't+Heat/207643 (accessed 2026-10-30)
- U.S. Consumer Product Safety Commission: recalls search. https://www.cpsc.gov/Recalls (accessed 2026-10-30)
- Federal Trade Commission: endorsement and affiliate disclosure guidance. https://www.ftc.gov/business-guidance/resources/ftcs-endorsement-guides-what-people-are-asking
- Part prices (Sears PartsDirect, S-list) and repair cost guides (Fixr G1, HomeGuide G2), see lists below (accessed 2026-10-30).
- ApplianceDB free developer sample (Whirlpool US dryer codes; cross-check only). Data under the Open Database License (ODbL) v1.0. https://github.com/ApplianceDB/ApplianceDB-public (accessed 2026-10-30)
Part price sources (Sears PartsDirect public search results, USD, accessed 2026-10-30; GE, LG, Samsung, Frigidaire, and Speed Queen parts excluded; prices change, confirm with your model number):
- S1. Search "whirlpool dryer thermal fuse" (the "amana dryer thermal fuse" search returned no listings): WP3390719 $19.10, WP3399849 $22.70, WP306604 $26.84, WP3392519 $42.30, WP53-1182 $45.78, WP8572767 $49.17, WP33001762 $49.40. https://www.searspartsdirect.com/search?q=whirlpool%20dryer%20thermal%20fuse
- S2. Search "amana dryer high limit thermostat": thermal cut-off fuse kit W11050897 $12.99; high-limit thermostats WP3977767 $13.74, WP303396 $26.84, WP3390291 $43.31, WP8573028 $52.67, WP3404153 $53.09, WP3404154 $65.79, WP8557403 (with inlet thermistor) $69.50, WP53-0771 $75.45, WP3391914 $78.59. https://www.searspartsdirect.com/search?q=amana%20dryer%20high%20limit%20thermostat
- S3. Search "amana dryer cycling thermostat": WP3398128 $15.01, WP694674 $39.66, WP3387134 $43.02, WP35001087 safety $46.05, WPY304474 $55.96, WPY304475 $57.51, WP8318268 $62.89, WP3387137 $64.16, WPY504514 $81.30, WP503979 $94.71, WP33303391 $98.40, WPW10168174 $113.22 (a high-limit and a heating element in the same results excluded). https://www.searspartsdirect.com/search?q=amana%20dryer%20cycling%20thermostat
- S4. Search "amana dryer heating element": 279838 $50.54, WPY503978 $59.30, WP3387747 $68.68, WP8544771 $98.21, Amana 61927 $109.26, WP35001247 $109.66, W10815654 $113.39, WP279843 $121.28, WP3387749 $138.96, WP3403591 $171.06, 37001139 $238.65, 61928 $265.69 (LG 5301EL1001J excluded). https://www.searspartsdirect.com/search?q=amana%20dryer%20heating%20element
- S5. Search "amana dryer igniter": kit 279311 $28.26, WP37001308 $35.12, 4391996 $36.64, WP33002789 $71.63. https://www.searspartsdirect.com/search?q=amana%20dryer%20igniter
- S6. Search "amana dryer gas valve coil": coil kit 279834 $26.08, WPW10368268 $54.67, secondary coil 58804B $65.85, kit WPW10328463 $68.11, booster and holding coil 58804A $93.60; Amana gas valve assembly W10622154 $223.72. https://www.searspartsdirect.com/search?q=amana%20dryer%20gas%20valve%20coil
- S7. Search "amana dryer flame sensor": radiant sensor WP338906 $25.91 (furnace and microwave parts excluded). https://www.searspartsdirect.com/search?q=amana%20dryer%20flame%20sensor
Pro-cost guide sources [GUIDE] (US national averages, parts + labor, not brand-specific quotes; the guide pages carry 2024–2025 dates, so local quotes may differ):
- G1. Fixr, "How much does it cost to repair a dryer?" (updated January 31, 2025): heating element replacement $150–$350; thermostat $100–$260; igniter $100–$250; coil $150–$300; vent replacement $75–$150; service fee $50–$80, labor $50–$100 per hour; dryers last 8–12 years; new dryer $600–$1,500. https://www.fixr.com/costs/dryer-repair (accessed 2026-10-30)
- G2. HomeGuide, "How Much Does Dryer Repair Cost? (2026)" (byline November 14, 2024): heating element $150–$350; thermal fuse $75–$150; thermostat $100–$300; control board $250–$500; igniter $100–$250; coil $100–$200; clogged vent $80–$185; minimum service fee $70–$130; new dryer $800–$1,200 (unit); dryers last 8–13 years on average. https://homeguide.com/costs/dryer-repair-cost (accessed 2026-10-30)
Disclosure
Fix It or Replace is an independent site. We are not affiliated with, endorsed by, or sponsored by Amana or Whirlpool. "Amana" and "Whirlpool" are trademarks of their owners and are used here only to describe the products we cover.
- Affiliate links: Some part links go to retailers such as PartSelect and RepairClinic. If you buy through them, we may earn a commission at no extra cost to you.
- Call line: Phone numbers labeled "partner pro" are operated by a third-party lead service that routes your call to an independent repair provider in your area. We may be paid for calls. We don't employ the technicians, and we don't guarantee their work, pricing, or availability. Confirm licensing, insurance, and quotes directly with the provider.
- Prices are estimates and change often. Always get a written quote.
- Safety: Unplug the dryer (and shut off gas) before working on it. If you smell gas, leave and call your gas utility. If you're unsure, call a qualified professional.
We don't publish fake reviews or testimonials, and we never present a tracking phone number as a specific local business.