Last updated: 2026-10-30 · By Fix It or Replace editorial team
Maytag Washer Not Spinning? Balance, Spin Setting, Suds, Drain Hose and Lid Lock Fixes — Costs and Repair vs Replace (2026)
Quick answer
Most Maytag "won't spin" calls are a setting, a load, or suds. Maytag Product Help lists these first:
- Unbalanced load. If the washer senses an off-balance load, it refills and rocks the basket to redistribute it (you may see Ofb). If that fails, it stops. Spread the load out and press Start/Pause.
- Spin setting. Low Spin or No Spin leaves clothes wet. Maytag notes the washer remembers settings per cycle, so a cycle you once ran with no spin stays that way. Delicate and Hand Wash spin slower on purpose.
- Bulky items. Use the Bulky or Sheets/Bedding cycle for comforters, coats, and blankets, not Normal or Rapid Wash. Balance a single heavy item with a few towels.
- Suds. Use only HE detergent and measure it. Maytag says too many suds reduce spin speed (top-loads may show Sud).
- Level the washer. An unlevel washer can't balance the load.
- Drain hose. Water standing in the tub means it can't reach spin: use the U-shaped hose form, put only 4.5 inches of hose into the standpipe, and keep the standpipe between 39 and 96 inches high (Maytag's top-load spin page; its drain guide says 30 inches minimum).
- Lid or door. Maytag says the washer only runs when the lid or door is securely closed. LdL means the lid can't lock: check for items under the lid and detergent build-up on the lock.
- Power failure during spin? It may not ramp up to full speed. Run Drain & Spin.
If those don't fix it, the usual parts are the lid lock (top-load) or door lock (front-load), a drive belt on belt-drive models, the shift actuator on many top-loads, the drain pump, the drive motor, or the control board. Maytag's 10-year limited parts warranty covers the drive motor on models made after 2017, so check it before paying for a motor.
Repair or replace? Most no-spin calls cost nothing to fix. A lid lock or actuator is usually worth fixing. A motor may be a parts-covered repair under Maytag's 10-year warranty. See the calculator below.
Our partner pro call line is coming soon. Until then: if your appliance may still be under warranty, contact the manufacturer first. Otherwise, get two or three written quotes from local appliance repair companies, and ask about the diagnostic fee and the parts-and-labor warranty.
Verdict at a glance
| Your situation | What it usually means | Our verdict |
|---|---|---|
| Clothes wet, Ofb, Sud, a Delicate or No Spin setting, a single bulky item | Balance routine, spin setting, suds, or load | ✅ Free fix. Rebalance, change the setting, Drain & Spin |
| Water standing in the tub; LdL; washer rocks | Drain hose or standpipe, lid lock blocked, not level | ✅ Free to cheap. Fix the hose, clear the lid, level; lid lock if it fails |
| Drains fine, lid locks, but the basket never spins; F# E# codes return | Belt, shift actuator, motor, motor control, board | 🔧 Usually worth repairing, especially if the drive motor is inside Maytag's 10-year parts coverage; ♻️ lean toward replacing for a board on an older washer |
Safety check before any DIY (30 seconds)
Stop and don't start the DIY steps below if any of these is true:
- Unplug the washer before you open any panel or take off the drain hose.
- The tub is full of water. Drain or bail it first; it's heavy and may be hot.
- Never bypass the lid lock or door lock. It keeps hands away from a spinning basket.
- You smell burning, see scorched wiring, or the breaker trips again. Stop and call a qualified technician.
- The washer is still under warranty (Maytag covers all parts and labor for the first year, and the drive motor and wash basket parts-only for 10 years on models made after 2017). Use Maytag service before you open panels.
- Recall check: search your model on the CPSC recall site before paying for a repair.
If none of these apply, the free checks below are safe for most owners.
Fix order at a glance (cheapest first)
| Order | What to try | Cost | DIY tier |
|---|---|---|---|
| 1 | Let the Ofb balance routine finish; then redistribute and press Start/Pause | Free | Easy |
| 2 | Check the spin setting (not Low/No Spin; remembered per cycle) | Free | Easy |
| 3 | Use Bulky or Sheets/Bedding for big items; add towels to a single item | Free | Easy |
| 4 | Measure HE detergent; rinse out suds | Free | Easy |
| 5 | Level the washer | Free | Easy |
| 6 | Fix the drain hose: U-form, 4.5 in into the standpipe, no tape, no kinks | Free | Easy |
| 7 | Clear items under the lid; clean detergent off the lid lock (LdL) | Free | Easy |
| 8 | After a power failure or F# E#: Start/Pause to clear; Drain & Spin | Free | Easy |
| 9 | Front-load: clean the drain pump filter (models that have one) | Free | Easy |
| 10 | Replace the lid lock, door lock, or drive belt | Part, or pro visit | Moderate |
| 11 | Replace the shift actuator or drain pump | Part, or pro visit | Moderate → Advanced |
| 12 | Drive motor, motor control, main board | Pro diagnosis first (check the 10-year warranty) | Advanced |
DIY tiers: Easy (no panels off) · Moderate (a panel off, power off) · Advanced (wiring connectors or several parts) · Pro only (mains wiring, or still under warranty).
Which Maytag washer do you have?
Find the model and serial number on the label (on most top-loads, under the lid or on the back of the cabinet; on front-loads, around the door opening). Maytag's warranty page uses the model number to show your exact coverage.
| Type | Model prefix (examples) | How it signals a spin problem | Notes |
|---|---|---|---|
| Top-load (agitator or impeller) | Often MVW (check label) | Ofb, Sud, LdL, OL, F# E# | Locks the lid before spinning |
| Front-load | Often MHW (check label) | Display codes; see your manual | Door must lock; pump filter on some models |
| Commercial-grade residential top-load | MVWP (check label) | As top-load | Extra 5-year parts and labor on named models |
| Laundry center | Varies | See manual | Shares Whirlpool-family parts |
Prefixes are examples, not a full list. Maytag is a Whirlpool Corporation brand, so many parts are Whirlpool-family part numbers.
Five-minute checks before you call anyone
- Let it rebalance. If you see Ofb, Maytag says let the washer finish its correction routine. If the dial is flashing and it stopped, redistribute, close the lid, and press Start/Pause.
- Spin setting. Pick a cycle with a high spin (Heavy Duty, Normal) and check Spin isn't set to Low or None for that cycle. Then run Drain & Spin.
- Load. Loose heaps evenly around the washplate. Don't add wet items mid-cycle. Wash a rug or jacket with a few towels. Comforters go on Bulky/Sheets.
- Suds. If you used regular detergent or too much HE detergent, run a rinse and measure next time.
- Level. Check all four feet touch the floor and the top is level side to side and front to back.
- Drain hose. U-form attached; only 4.5 in (113 mm) into the standpipe; no tape over the opening; no kinks; standpipe height within Maytag's limits.
- Lid / door. Nothing under the lid; wipe detergent build-up off the lid lock area; nothing heavy sitting on the lid (LdU).
- Codes. For F# E#, Maytag says press Start/Pause once to clear, then again to restart. If it doesn't clear, schedule service.
- Front-load pump filter. On models with an access door, clean the drain pump filter per your manual.
How to know it's fixed: Drain & Spin on a balanced load drains the water and reaches full spin with no Ofb, LdL, Sud, or F# E#, and clothes come out damp, not dripping.
Maytag washer codes linked to "not spinning"
Maytag lists these top-load codes on its US Product Help pages ("may not be all codes for your model"; your manual has the full list).
| Code | Maytag's meaning | What to do |
|---|---|---|
| Ofb | Load out of balance; the washer is running a balance-correction routine | Let it continue; if it stops with the dial flashing, redistribute, close the lid, press Start/Pause |
| OL | Load too large | The washer drains; remove several items, add HE detergent, close the lid, press Start/Pause |
| Sud | Excessive suds | Use only measured HE detergent |
| LdL | Lid not locking | Remove items under the lid; clean detergent build-up around the lid lock |
| LdU | Lid can't unlock | Remove objects such as a laundry basket from the lid |
| lid | Lid left open | Close the lid; after 10 minutes the cycle resets and drains |
| drn | Not draining properly (sometimes an installation problem) | Check the drain hose and standpipe |
| PF | Power failure interrupted the cycle | Touch and hold Start to restart, or press Power to clear |
| F# E# or F## | System error | Start/Pause once to clear, again to restart; schedule service if it won't clear |
Which part each code points at, and how hard the fix is:
| Code / symptom | Part most often involved | First fix (free) | If it comes back | DIY tier |
|---|---|---|---|---|
| Ofb every load | Leveling, suspension springs or rods | Rebalance; level | Suspension parts | Moderate |
| LdL | Lid lock, lid strike | Clear the lid; clean the lock area | Lid lock assembly | Moderate |
| Front-load won't spin, door won't lock | Door lock | Close the door firmly; clear the gasket | Door lock | Moderate |
| drn, water in the tub | Drain hose, pump filter, drain pump | Fix the hose; clean the filter | Drain pump | Easy → Advanced |
| Agitates but won't spin (top-load) | Shift actuator, belt | Power-cycle; Drain & Spin | Actuator or belt | Moderate |
| Motor hums, basket still | Drive motor, motor control board | — | Motor (check 10-year coverage) or board | Advanced |
| F# E# returns | Control or sensor fault | Clear with Start/Pause | Board diagnosis | Advanced |
Code meanings from Maytag US Product Help "Error Codes On Maytag Top Load Washers"; steps from "Not Spinning - Washer", "Not Spinning - Front Load Washer", and "Washer Not Draining or Spinning? Troubleshooting Guide" (sources 1–4), checked directly 2026-10-30. The open ApplianceDB sample (source 11), which maps manufacturer codes to a component, a ranked fix, and a DIY difficulty, has no Maytag entries, so the code→part table above is our own mapping from Maytag's pages and the part catalog, not Maytag wording. Maytag shares many codes with Whirlpool-family washers; see our Whirlpool washer not spinning guide for the same family.
Diagnose by symptom → likely part
Before you touch parts: Unplug the washer. Drain or bail out the water. Towels down. Keep the model number handy.
1. LdL, or it never locks and never spins
Likely causes: something under the lid, detergent build-up on the lock, a damaged lid strike, or a failed lid lock assembly (top-load). Front-loads: a failed door lock.
DIY difficulty: Moderate (top panel or console up, power off).
| Part | What it does | DIY difficulty |
|---|---|---|
| Lid lock assembly | Locks the lid before high-speed spin | Moderate |
| Door lock (front-load) | Locks the door and tells the control it's shut | Moderate |
2. Ofb on normal loads; shakes and stops
Likely causes: the washer isn't level, or worn suspension springs or rods let the tub sway.
DIY difficulty: Moderate.
| Part | What it does | DIY difficulty |
|---|---|---|
| Suspension springs / rods | Hold and damp the tub | Moderate |
3. Agitates fine, but the basket never spins (top-load)
Likely causes: a failed shift actuator (it switches the drive between agitate and spin on many direct-drive top-loads), or a worn drive belt on belt-drive models.
DIY difficulty: Moderate (washer tipped back, power off).
| Part | What it does | DIY difficulty |
|---|---|---|
| Shift actuator | Switches between wash and spin | Moderate |
| Drive belt | Connects the motor to the transmission | Moderate |
4. Water stays in the tub; drn
Likely causes: the drain hose setup, a clogged pump filter (front-load), or a failed drain pump.
DIY difficulty: Easy (hose, filter) to Advanced (pump).
| Part | What it does | DIY difficulty |
|---|---|---|
| Drain pump | Pumps water out before spin | Advanced |
5. Motor hums or stays silent; F# E# keeps coming back
Likely causes: the drive motor, the motor control board, or the main control board.
DIY difficulty: Advanced; diagnose first. If the washer was made after 2017, Maytag's 10-year limited parts warranty covers the drive motor; you'd pay labor after year 1.
| Part | What it does | DIY difficulty |
|---|---|---|
| Drive motor | Turns the basket | Advanced (check warranty) |
| Control board / motor control | Runs the cycle and the motor | Advanced; diagnose first |
Not sure if it's the lock, the actuator, or the motor? A technician can test each in one visit and tell you whether Maytag's motor warranty applies; that's the visit that decides repair vs. replace.
Partner pro call line coming soon. See “who services” below for your options.
Independent partner service, not Maytag. We may be paid when you call.
Keep it spinning
- Measure HE detergent every load (Maytag).
- Wash several items, not one heavy item; use Bulky/Sheets for bedding.
- Keep it level, and recheck after moving it.
- Keep the drain hose in its U-form, 4.5 inches into the standpipe, untaped.
- Front-load: clean the drain pump filter occasionally (Maytag).
- Register the washer so Maytag can confirm your 10-year coverage later.
Related guides
- Whirlpool washer not spinning
- GE washer not spinning
- Whirlpool washer won't drain
- Samsung washer not spinning
What Maytag's warranty covers on a washer
Per Maytag's US "10-Year Limited Parts Warranty" page (see Sources); your model's warranty document has the final terms:
| Period | What's covered | Who pays labor |
|---|---|---|
| Year 1 | All parts and labor (Maytag major laundry appliances made after 2017) | Maytag |
| Years 2–10 | Limited parts coverage on the drive motor and wash basket (washers) | You pay labor |
| Bonus (named models) | MVW6230RH: 5-year limited parts and labor, then parts-only on the motor and basket to year 10. MVWP586GW: all parts and labor for 5 years, plus the 10-year parts coverage (single-family, non-commercial use) | See model warranty |
What this means for a washer that won't spin: in year 1, any failed part is covered. After that, a drive motor is still a covered part through year 10 on eligible models, so a motor repair may cost you labor only. A lid lock, actuator, belt, pump, or board after year 1 is on you unless you have one of the bonus-coverage models or an extended service plan. Settings, suds, and installation problems (hose, level) aren't defects.
→ Maytag: 10-year limited parts warranty and model lookup · Maytag Customer Service 1-800-344-1274 (from Maytag Product Help)
Before you pay for any repair: a 4-point check
- Warranty: year 1 parts and labor; drive motor parts to year 10 (made after 2017); bonus coverage on named models; plus retailer or credit-card extended protection or a Maytag extended service plan.
- Recalls: search your model at the U.S. Consumer Product Safety Commission's recall site: cpsc.gov/Recalls. A recall repair is free.
- Free fixes done: balance routine, spin setting, Bulky cycle, HE detergent, level, drain hose, lid lock area, code clear, Drain & Spin.
- Written quote: ask for part, labor, and trip fee as separate lines, and whether the part is covered by Maytag's 10-year warranty.
What it costs: repair parts and pro service (2026)
How we price this table: DIY part prices are Maytag and Whirlpool-family part numbers (Maytag is a Whirlpool Corporation brand) listed on Sears PartsDirect public search pages for Maytag washer parts (S-list under Sources), USD before tax and shipping; ranges span several part numbers because the right part depends on your model number. Pro costs tagged [GUIDE] come from two US cost guides (Fixr = G1, HomeGuide = G2): national averages for washers in general unless noted, not Maytag-specific quotes. "Varies — get a quote" means neither guide itemizes that repair, so we don't show a number.
| Repair | Part cost (DIY) | Typical pro cost (parts + labor) | Notes |
|---|---|---|---|
| Rebalance, spin setting, detergent, level, hose, code clear | $0 | — | Do these first |
| Lid lock assembly | $49.07–$134.55 (W10404050 to W10919224) [S1] | [GUIDE] lid switch $85–$160 (G1); door lock or lid switch $100–$300 (G2) | LdL that won't clear |
| Front-load door lock | $64.00–$244.86 (WPW10443885 to WP22003593) [S7] | [GUIDE] door lock $110–$200 (G1) | |
| Drive belt | $16.29–$52.92 (WP21352320 to WPW10388418) [S8] | [GUIDE] belt $100–$200 (G2) | Belt-drive models only |
| Shift actuator | $13.57–$73.62 (W10913952 to W11481722) [S3] | Varies — get a quote (not itemized in G1/G2) | Common on direct-drive top-loads |
| Suspension springs | $4.70–$50.19 (WP21001598 to W10135004 2-pack) [S6] | [GUIDE] shock absorbers $100–$350, full set (G2); $150–$300 (G1) | |
| Drain pump | $35.14–$249.70 (WP3363394 to WPW10321032) [S4] | [GUIDE] pump $150–$350, part $20–$100 (G2); pump $300–$400 (G1) | If water stays in the tub |
| Drive motor | $138.89–$284.76 (WP661600 to WPW10140581) [S2] | [GUIDE] motor $300–$500 (G1); $300–$700 (G2) | Parts covered to year 10 on eligible models |
| Control board | $171.58–$396.95 (W10480130 to W10393448) [S5] | [GUIDE] motherboard $250–$400 (G1); control board $350–$550 (G2) | Diagnose first |
| Maytag washer repair (brand range) | — | [GUIDE] Maytag $175–$350 (G1, brand-specific, all repair types) | |
| Service call / diagnostic fee | — | [GUIDE] $50–$100 diagnosis visit (G1); $70–$130 minimum service fee, then $50–$125 per hour (G2) | |
| New comparable washer | — | [GUIDE] $650–$2,100 replacement (G1); $700–$1,300 new washer (G2); all brands | Add haul-away if not included |
Part prices checked 2026-10-30 on Sears PartsDirect public search pages (S1–S8). Pro-cost cells tagged [GUIDE] from G1 (Fixr) and G2 (HomeGuide), re-read 2026-10-30; [GUIDE] figures are national averages, not Maytag-specific quotes except where marked. Prices change; confirm with your model number.
Tip: if a tech says "motor," ask them to confirm the build date. On a Maytag made after 2017, the motor part should go through Maytag's warranty.
Repair vs. replace calculator
1. What's the all-in repair cost? → R = trip/diagnostic fee + part + labor + tax, minus anything Maytag's warranty (or a recall) covers
2. What does a comparable new washer cost, all-in? → N = unit + delivery + installation + haul-away (+ new hoses)
3. How old is your washer, and how long should it last? → Age and Life (use about 10 years, near the middle of HomeGuide's 8–13-year range, if you don't know)
4. How much have you spent on repairs in the last 2 years? → Past
Step A — Cost ratio: R ÷ N
Step B — Life used: Age ÷ Life
Step C — Repeat-repair check: (R + Past) ÷ N
| Life used under 50% | Life used over 50% | |
|---|---|---|
| Repair under 50% of new | ✅ Repair | 🤔 Repair is usually fine. Check for other wear |
| Repair over 50% of new | 🤔 Get a second quote first | ❌ Replace |
Repeat-repair rule: if Step C is over 50%, treat it like the bottom-right box: money keeps going into the same machine. And if the part is no longer available for your model, that decides it: replace.
Worked example 1 (illustrative numbers): A 2-year-old Maytag top-load leaves towels soaking wet. The Normal cycle had been saved with No Spin after a delicate load. R = $0.
→ Not a repair.
Worked example 2 (illustrative numbers): A 6-year-old Maytag (made after 2017) has a failed drive motor. The motor part is covered by the 10-year warranty; you pay the visit and labor: R = $200; N = $950; no other repairs.
200 ÷ 950 = 21%; life used 6 ÷ 10 = 60%; repeat check 21% → Repair (usually fine; check for other wear).
Worked example 3 (illustrative numbers): A 9-year-old Maytag needs a main control board (not on the 10-year list) after a $250 drain pump last year. R = $500; N = $950.
500 ÷ 950 = 53%; life used 9 ÷ 10 = 90%; repeat check (500 + 250) ÷ 950 = 79% → Replace.
Tips toward replacing: a board on a washer near 10 years old, a second big repair in about 2 years, or rust or a cracked tub.
Tips toward repairing: it's a lid lock, actuator, belt, or springs; the washer is under about 7 years old; or the motor part is inside Maytag's 10-year coverage.
Why 50%? It's the common rule of thumb, and the one we use. Some technician checklists draw the line a little higher, at about 60% of a new washer's price, so treat a repair that costs 50–60% of new as a second-quote zone, not an automatic replace. The older the washer, the lower the line should go: once it has used more than half its expected life, the same repair buys fewer years.
Who services Maytag washers near you
1. Maytag (warranty or preferred service providers). In year 1, for a motor through year 10, or on a bonus-coverage model, start with Maytag. Maytag's Product Help schedules service from its preferred list of providers.
→ Maytag: schedule service / warranty lookup · 1-800-344-1274
2. A partner appliance pro (out of warranty).
Our call line connects you with an independent appliance repair provider in your area. Tell them the code (Ofb, LdL, Sud, F# E#), whether it agitates, whether it drains, and your model number.
Our partner pro call line is coming soon. Until then: if your appliance may still be under warranty, contact the manufacturer first. Otherwise, get two or three written quotes from local appliance repair companies, and ask about the diagnostic fee and the parts-and-labor warranty.
3. DIY with the right part. Lid locks, actuators, belts, and springs are common DIY jobs. Order by your exact model number.
Questions to ask any technician:
- Did you check the spin setting, balance, detergent, level, and drain hose first?
- Is it the lock, the actuator, the motor, or the board? How did you confirm it?
- Is the part covered by Maytag's 10-year warranty on my model?
- Can you split the quote into part, labor, and trip fee?
Optional: is an appliance warranty worth it?
A home warranty (service contract) can cover repairs for a yearly fee plus a per-visit service fee. Read the exclusions carefully: many plans exclude problems caused by overloading or installation. A washer that's already broken is usually not covered. Maytag sells extended service plans on new appliances and advertises savings when you buy within 30 days of purchase.
FAQ
Why is my Maytag washer not spinning?
Maytag's list: an unbalanced load, Low or No Spin selected (remembered per cycle), a delicate cycle, a single bulky item, too much or non-HE detergent, an unlevel washer, a drain hose problem, or a power failure during spin. The lid or door must also lock.
What does Ofb mean on a Maytag washer?
The load is out of balance and the washer is running a correction routine. Let it continue. If it stops with the dial flashing, redistribute the load, close the lid, and press Start/Pause.
What does LdL mean on a Maytag washer?
The lid isn't locking. Check for items directly under the lid and detergent build-up around the lid lock.
Why are clothes soaking wet after a Maytag wash?
Usually a low-spin or no-spin setting, a delicate cycle, suds from too much detergent, or an unbalanced load. Run Drain & Spin after fixing the cause.
How do I clear an F# E# code on a Maytag washer?
Press Start/Pause once to clear it, then press Start/Pause again to restart. If it won't clear, schedule service.
Does Maytag's 10-year warranty cover a washer that won't spin?
It covers the drive motor and wash basket as parts for 10 years on Maytag washers made after 2017, plus all parts and labor in year 1. After year 1, you pay labor, and parts like the lid lock or board aren't on the 10-year list.
How high should a Maytag drain standpipe be?
Maytag's top-load spin page says 39 to 96 inches; its drain guide says 30 to 96 inches. Only 4.5 inches of hose should go into the standpipe, and don't tape the opening.
Is it worth fixing a Maytag washer that won't spin?
Usually. Most causes are free, and lid locks and actuators are cheap parts. A motor may be a warranty part. A board on a washer near 10 years old leans toward replacing. Use the calculator above.
About the author
Fix It or Replace editorial team — We research appliance repairs using manufacturer documentation, parts-supplier data, and current US cost guides, and we cite every source below. We are not appliance technicians; for anything involving wiring, call a qualified pro.
Last updated: 2026-10-30.
Sources
- Maytag US Product Help: "Not Spinning - Washer" (top-load: out-of-balance self-correction by refilling and rotating, error if it fails; Low/No Spin; Drain & Spin; Bulky or Sheets/Bedding for bulky items, not Normal or Rapid Wash; Add a Garment; standing water: U-shaped hose form, only 4.5 in (113 mm) in the standpipe, no tape, standpipe 96 in max and 39 in min, kinks; level; power failure during spin; Customer Service 1-800-344-1274). https://producthelp.maytag.com/Laundry/Washers/Top_Load_Washer/Cycle_Concerns/Not_Spinning_-_Washer (accessed 2026-10-30)
- Maytag US Product Help: "Not Spinning - Front Load Washer" (Low/No Spin; settings remembered per cycle; Delicate and Hand Wash spin slower; HE detergent, measure, excess suds reduce spin speed; single bulky item; overloaded; level; drain hose 4.5 in, standpipe 39–96 in). https://producthelp.maytag.com/Laundry/Washers/Front_Load_Washers/Not_Starting_or_Not_Operating/Not_Spinning/Not_Spinning_-_Front_Load_Washer (accessed 2026-10-30)
- Maytag US Product Help: "Washer Not Draining or Spinning? Troubleshooting Guide" (lid or door switch, washer operates only when securely closed; unbalanced or overloaded; spin speed by cycle; excessive suds; drain hose kinks or clogs, U-form; standpipe 96 in max and 30 in min; front-load drain pump filter on some models). https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Washer_Not_Draining_or_Spinning%3F_Troubleshooting_Guide (accessed 2026-10-30)
- Maytag US Product Help: "Error Codes On Maytag Top Load Washers" (drn; F# E# or F##, Start/Pause to clear; HC reversed hoses; LdL; LdU; LF/Lo FL/F8 E1; lid, 10 minutes; Ofb; OL; PF; Sud). https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers (accessed 2026-10-30)
- Maytag US: "Maytag 10-Year Limited Parts Warranty" (all major kitchen and laundry appliances made after 2017; all parts and labor in year one; washers and dryers: drive motor, wash basket, dryer drum; MVW6230RH labor covered for the first 5 years (footnote: 5-year limited parts and labor plus an additional 5-year limited parts warranty on drive motors and the stainless steel wash basket); MVWP586GW all parts and labor for 5 years plus 10-year limited parts, single-family non-commercial use; see product warranty for details). https://www.maytag.com/services/limited-10-year-warranty.html (accessed 2026-10-30)
- U.S. Consumer Product Safety Commission: recalls search. https://www.cpsc.gov/Recalls (accessed 2026-10-30)
- Federal Trade Commission: endorsement and affiliate disclosure guidance. https://www.ftc.gov/business-guidance/resources/ftcs-endorsement-guides-what-people-are-asking
- Part prices: Sears PartsDirect public search pages, see S-list below (accessed 2026-10-30).
- Repair cost guides: Fixr (G1) and HomeGuide (G2), see list below (accessed 2026-10-30).
- Whirlpool-family cross-reference: our Whirlpool washer not spinning guide (Whirlpool US Product Help, same code family).
- ApplianceDB free developer sample (checked for Maytag US washer codes; none in the sample, so not used for this page's tables). Data under the Open Database License (ODbL) v1.0. https://github.com/ApplianceDB/ApplianceDB-public (accessed 2026-10-30)
Part price sources (Sears PartsDirect public search results for Maytag washer parts, USD, accessed 2026-10-30; Maytag and Whirlpool-family part numbers only, other brands excluded; prices change, confirm with your model number):
- S1. Search "maytag washer lid lock": lid lock assemblies W10404050 $49.07, WPW10619844 $75.46, W10810403 $79.65, W11188327 $106.96, W11307244 $113.65, W10919224 $134.55 (bezels, strikes, and the GE lid lock excluded). https://www.searspartsdirect.com/search?q=maytag%20washer%20lid%20lock
- S2. Search "maytag washer drive motor": WP661600 $138.89, W11026785 $194.12, W11191299 laundry center $209.06, W11039788 $221.85, WPW10140581 $284.76 (motor stator W10365754 $382.95 and rotor W10365755 $32.17 listed separately; belts excluded). https://www.searspartsdirect.com/search?q=maytag%20washer%20drive%20motor
- S3. Search "maytag washer shift actuator": W10913952 $13.57, W10913953 $36.24, W11511138 $41.89, WPW10006355 $55.31, W11481722 $73.62 (gear case, refurbished, commercial, dispenser, and brake actuators and Crosley part excluded). https://www.searspartsdirect.com/search?q=maytag%20washer%20shift%20actuator
- S4. Search "maytag washer drain pump": WP3363394 $35.14, WPW10661045 $50.55, WPW10605427 $51.75, WPW10581874 $81.54, WP3363892 $81.60, WPW10409079 $87.86, W10876600 $103.67, WPW10403802 $149.96, WP25001052 $151.05, WP34001098 $151.86, WP22003059 $151.87, WP34001320 $195.40, W10919003 $204.68, WPW10321032 $249.70 (hoses and filters excluded). https://www.searspartsdirect.com/search?q=maytag%20washer%20drain%20pump
- S5. Search "maytag washer control board": Maytag electronic control boards W10480130 $171.58 to W10393448 $396.95 (17 listings); motor control board WPW10384843 $274.68. https://www.searspartsdirect.com/search?q=maytag%20washer%20control%20board
- S6. Search "maytag washer suspension spring": WP21001598 $4.70, WP63907 $7.27, W11266650 $9.69, W11266649 $12.85, W10135004 2-pack $50.19 (bracket and LG, Samsung, Frigidaire, GE springs excluded). https://www.searspartsdirect.com/search?q=maytag%20washer%20suspension%20spring
- S7. Search "maytag washer door lock": WPW10443885 $64.00, WPW10482836 $78.57, WP8183270 $134.79, WPW10306374 $146.33, WPW10253483 $158.95, WPW10192995 $172.13, WP22004435 $183.27, WPW10375379 $200.52, WP22003593 $244.86 (switches, strikes, clips, and hooks excluded). https://www.searspartsdirect.com/search?q=maytag%20washer%20door%20lock
- S8. Search "maytag washer belt": WP21352320 $16.29, WPW10006384 $23.88, W11239857 $33.98, WP27001006 $36.92, WPW10192984 $37.63, WP22003483 $38.63, WPW10388414 $42.68, WP27001007 $47.65, WPW10006388 $48.97, WPW10388418 $52.92 (belt kits excluded). https://www.searspartsdirect.com/search?q=maytag%20washer%20belt
Pro-cost guide sources [GUIDE] (US national averages, parts + labor, not brand-specific quotes unless noted; the guide pages carry 2023–2025 dates, so local quotes may differ):
- G1. Fixr, "How much does it cost to repair a washing machine?" (updated January 31, 2025): average $150–$400; lid switch $85–$160; door lock $110–$200; shock absorber $150–$300; pump $300–$400; motherboard $250–$400; motor $300–$500; Maytag washer repair $175–$350; diagnosis visit $50–$100; replacement $650–$2,100. https://www.fixr.com/costs/washing-machine-repair (accessed 2026-10-30)
- G2. HomeGuide, "How Much Does Washing Machine Repair Cost? (2026)" (byline April 5, 2023): average $100–$400; door lock or lid switch $100–$300; belt $100–$200; shock absorbers $100–$350 (full set); pump $150–$350 (part $20–$100); control board $350–$550; motor $300–$700; minimum service fee $70–$130, then $50–$125 per hour; new washer $700–$1,300; washers last 8–13 years. https://homeguide.com/costs/washing-machine-repair-cost (accessed 2026-10-30)
Disclosure
Fix It or Replace is an independent site. We are not affiliated with, endorsed by, or sponsored by Maytag or Whirlpool Corporation. "Maytag" is a trademark of its owner and is used here only to describe the products we cover.
- Affiliate links: Some part links go to retailers such as PartSelect and RepairClinic. If you buy through them, we may earn a commission at no extra cost to you.
- Call line: Phone numbers labeled "partner pro" are operated by a third-party lead service that routes your call to an independent repair provider in your area. We may be paid for calls. We don't employ the technicians, and we don't guarantee their work, pricing, or availability. Confirm licensing, insurance, and quotes directly with the provider.
- Prices are estimates and change often. Always get a written quote.
- Safety: Unplug the washer before opening panels or removing hoses. If you're unsure, call a qualified professional.
We don't publish fake reviews or testimonials, and we never present a tracking phone number as a specific local business.